Solar Panel Drain Clips for 30, 32, 35 & 40 mm Frames – Solar Draino™

Solar panel drain clips that snap onto the bottom edge of framed panels and stop rainwater pooling on the glass and against the frame. Solar Draino™ clips guide rainwater away from the panel edge and reduce the dirt bands and soiling that build up on low-tilt and flat-roof arrays, and fit in seconds with no tools.

  • Sizes for 30, 32, 35 and 40 mm frames
  • Packs of 100, 500 and 1,000, plus 25 and 50 for 30 mm
  • UV-stabilised engineering plastic
  • UK stock, with trade pricing available

Price range: £24.75 through £850.00 +VAT

SKU: SCR-SD

Got a question about this product?

Solar Panel before Solar Draino Installed Solar Panel After Solar Draino Installed

Slide to compare: without drain clips, rainwater pools against the frame and leaves a dirt band across the bottom cells. With Solar Draino™ clips fitted, the water drains away and the edge stays clearer between cleans.

Solar Panel Drain Clips – Stop Water Pooling on Low-Tilt Panels

On low-tilt and flat-roof arrays, the panel frame traps rainwater along the bottom edge of the glass. As it evaporates it leaves a band of dirt that can shade the cells and reduce output, and it is one of the hardest areas to keep clean. Solar Draino™ drain clips snap onto the bottom edge of the frame and create a drainage path, so water runs off the panel instead of sitting against the frame. Also known as solar panel drainage clips, water drain clips, drip clips, rain clips, water guide clips and siphon (syphon) clips.

Why Bottom-Edge Soiling Costs You Energy

On low-tilt panels, the frame sits slightly proud of the glass. Rainwater collects against it, and as it dries it leaves a band of dirt along the bottom row of cells. Rain alone rarely clears it, so it builds up between cleans. That small band has a big effect. Solar cells are wired in strings, so shading even part of one cell can trigger a bypass diode and switch off a whole section of the panel. Published research on low-tilt rooftop arrays has measured power losses of 9% from soiling covering just 0.5% of a panel, and over 20% where 5–10 cm dirt bands formed along the bottom edge. Solar Draino™ drain clips give that water somewhere to go. By draining it off the panel instead of letting it pool, they help stop the soiling band forming, keep the bottom row of cells clearer for longer between cleans, and help protect your energy yield.

Ideal for East–West Flat Roof Systems

East–west solar arrays are now one of the most common layouts on UK flat roofs. The panels are mounted back-to-back at a low tilt – typically between 5° and 15° – which keeps wind loading down and fits more panels on the roof. That low angle is exactly why they suffer from bottom-edge soiling. At such a shallow pitch, rainwater can’t clear the frame lip, so water and dirt sit along the lower edge of every panel. Solar Draino™ clips give that water a drainage path on both the east- and west-facing rows.

Easy to retrofit

The clips push straight onto the existing panel frame – no tools, drilling, adhesives or changes to the mounting system. They can be fitted to an existing east–west array in one visit, ideally straight after a professional clean, so the panels start clean and stay cleaner for longer.

Which Size Do I Need?

Measure the depth of your panel frame – the side edge, from the front of the glass to the back of the frame – and choose the matching clip.
Frame depth Pack sizes available
30 mm drain clips 25, 50, 100, 500, 1,000
32 mm drain clips 100, 500, 1,000
35 mm drain clips 100, 500, 1,000
40 mm drain clips 100, 500, 1,000
All sizes have an 11.5 mm upper lip that sits on the front face of the panel.

How Many Clips Do I Need?

We recommend 2 clips per panel along the bottom edge, positioned roughly one-third and two-thirds of the way along.
Panels Clips needed Suggested pack
Up to 12 Up to 24 25 (30 mm only)
Up to 25 Up to 50 50 (30 mm only)
Up to 50 Up to 100 100
Up to 250 Up to 500 500
Up to 500 Up to 1,000 1,000

Installation

  1. Clean the panel, paying attention to the bottom edge of the glass and frame.
  2. Push the clip onto the bottom edge of the frame until it locks in place – no tools, screws or adhesive.
  3. Repeat for each panel, concentrating on rows where water naturally pools.
For best results, fit the clips straight after a professional clean.

Where to Use Them

  • East–west flat roof arrays
  • Low-pitch residential roofs
  • Flat commercial and industrial roofs with long rows of panels
  • Ground-mount arrays at low tilt angles
  • Retrofit on existing systems that already show dirt bands along the bottom edge

Specification

  • Material: UV-stabilised engineering plastic, black
  • Frame sizes: 30, 32, 35 and 40 mm
  • Upper lip: 11.5 mm
  • Heat deflection temperature: 102 °C+
  • Good high and low temperature resistance and chemical resistance
  • Expected service life: up to 15 years in European conditions

Frequently Asked Questions

Why plastic and not stainless steel?

Engineering plastic will not scratch the glass or frame, does not corrode, and has excellent UV stability for long-term outdoor use.

Can I mix sizes in one order?

Yes – add each size to your basket separately, or contact us for a mixed trade order.

Can the clips be removed?

Yes, they can be unclipped from the frame without tools.

Trade & Bulk Orders

Installers, solar cleaners and O&M companies: contact us for trade pricing on larger quantities. All sizes are held in stock in the UK.
solar-clean-robotics_header_265x70-150dpi_Neg_01
Start a Conversation

We would love to speak with you.
Feel free to reach out using the contact form.

Blog Posts

How to Remove Moss from Your Solar Panels

Moss buildup on solar panels reduces energy output and can damage your system. Learn what causes moss to grow and how to remove it safely using QLEEN / RotaQLEEN systems and Chemitek solar cleaning solutions from Solar Clean Robotics UK.

Read More »

Lets start a conversation

Submit your details, we will then contact you